FIVE-YEAR LIMITED WARRANTY ON FACTORY FINISHED INTERIOR DOORS  

This warranty is effective for all products manufactured or sold after August 1, 2004 .  Sun Mountain doors are warranted to be of sound material and workmanship and to be free of defects which would cause the door to be unfit for ordinary recommended use for the period of twelve (12) months from the date of shipment.  In addition, interior doors which have been prefinished by Sun Mountain are warranted for an additional four (4) years.  This extended warranty applies only to the construction of the door, and not the factory finish itself.  See our Finishing and Care Instructions below for details on finish maintenance.  

If a defect is discovered or occurs within one year from the date of shipment, written notice must be provided to Sun Mountain, Inc.  Buyer shall not return any goods to Sun Mountain until Sun Mountain has been provided a reasonable opportunity to inspect the goods at Buyer’s premises to determine whether a defect exists.  Sun Mountain will not be liable for any doors repaired, returned, or replaced without prior written consent.  If warranted doors contain defects covered under this limited warranty, Sun Mountain shall be limited to, at Sun Mountain ’s option, repairing or replacing the doors or to refunding the purchase price of the doors to Buyer.  Doors will be replaced in the same stage of fitting and/or finishing as they were originally supplied.  Sun Mountain will not pay any cost to remove defective doors or to install new doors, nor are we responsible for any finishing costs or consequential damages.  Final warranty inspection will be made at Sun Mountain ’s factory upon receipt of defective product.  If claim is found to be invalid, neither credit nor refund will be issued for the replacement door or the original door.  

This limited warranty does NOT apply to any of the following:

·    Doors more than 8’ tall or 3’6” wide.

·    Lited doors or one-panel wood doors over 6’8” tall or 3’ wide.

·    Doors that have warp which does NOT exceed 1/4” in the plane of the door
     (see below).

·    Doors less than 1-3/4” thick for exterior use.

·    Doors which have not been properly sealed on all six sides within 14 days of
     delivery, including the top and bottom edges of the door.

·    Damage caused by failure to comply with the Finishing and Care Instructions
     (see below).

·    Damage due to improper or incorrect installation.

·    Exterior doors used in a commercial application.

Damage caused by others or by any cause beyond the control of Sun Mountain, including but not limited to damage caused by misuse, abuse, accident, mishandling or by fire, flood, earthquake, storm, tornado or other acts of nature.

Misuse of a door, including but not limited to, using a door on part of a building without providing adequate overhang or an appropriate finish color.  Adequate overhang depends on the typical weather conditions of the site where the building is located, but typically means an overhang projecting a distance away from the door at least equal to one-half the elevation difference between the bottom of the door and the base of the overhang structure.  In order to reduce the chance of warping or checking, dark-colored finishes should be avoided on all exterior surfaces, especially if the door is exposed to direct sunlight.

Discoloration or rusting of decorative metal accents (clavos, grilles, strap hinges, etc.)

Damage due to trimming the door more than 1/2” from the top or 1-1/2” from the bottom of the slab.

Panel movement (shrinkage).  The panels in your door are designed to “float”, and will expand or contract in response to environmental conditions.

Expansion or contraction due to varying environmental conditions, such as temperature and humidity.

Gates, or doors used in a gate application.

The appearance of any field finished door.  

In addition, the following natural properties and characteristics add to the beauty of real wood doors and are not considered defects:  

On all knotty wood doors, the location, quantity, and size of knots is predictable.  Knots which show light through the door will be filled.  Knots which do not show light through the door and are not filled should be expected and are not considered defects.

In all species, natural variations in the color, texture, and density of the wood is common and always acceptable.

On wirebrushed doors, an inconsistent face plane where stiles or mullions meet rails is acceptable up to a depth change of 1/16", and apparent open connection between stiles and rails is acceptable to a width of 1/32".

On cedar doors, surface checks of up to 1/32" in width are acceptable and do not compromise the structural integrity of the door.  

For the purposes of this warranty, warp is defined as any distortion in the door itself and does not refer to the relationship of the door to the frame or jamb in which it is hung.  The term “warp” includes bow, cup and twist.  In measuring the amount of warp in a door, the following method shall be used: Bow, cup and twist shall be measured by placing a 7' straightedge on the suspected concave face of the door at any angle with the door in its installed position.  The measurement of warp shall be made at the point of maximum distance between the bottom of the straightedge and the face of the door.  

If the claimed defect is warp, Sun Mountain may defer repairing or replacing the door for a period of up to twelve (12) months from the date of claim or date of installation, in order to permit conditioning and equalizing to humidity and temperature conditions.  The deferral period will not be counted against the one-year warranty period.
 

Request Proposal :